The O’ring Adaptor is designed to allow for ground movement relative to the house downpipe.
(a) Overcomes the two fixed points struggle
(b) Overcomes reactive soil movement
Assemble downpipe,
Slip on O-Ring Adaptor - use o-ring lubricant
Tested to 3m head for tank jobs.
Can accommodate about 5˚ misalignment
Take care - there are no scratches on the 90 D/P at O-Ring seal.
Where this joint is underground, tape it to prevent particle entry to O-Ring area.
This fitting allows for ground movement relative to the house
The In Pipe Bolted Trap Screw suits 100mm DWV Pipe inspection openings. It is designed so that it can fit existing pipes, for repairs to damaged inspection openings, or simply for replacement of old bolted trap screws. Our In Pipe Bolted Trap Screw is a Watermark Product.
The Guzzla 100mm Inpipe ORG finishing collar and grate in designed to be fitted with a black high density polyethylene surround, which is replaceable, tough, light weight and whipper snipper resistant. And is supplied as a complete unit.
Your simple effective joiner for repairs and additions to stormwater pipes.
Step 1. Slide socket on the pipe past the joint zone.
Step 2. Just glue both sides of joining pipes
Step 3. Then slip the socket over the glued joints quickly
while glue remains wet.
Easy Joining to 90 stormwater pipe that has been cut or broken off at slab level. No more chiselling concrete before you can join up again. Joins inside pipe to outside pipe. Can fit over 90mm pipe one end, or inside 90mm pipe the other end.
The Blank / Reducer is a product of ours that has been designed for a couple of different uses, and like most of our other products are also designed to make your work easier.
The two different uses for this product are: Reduce any outlet on our Agy Tee to enable smaller agy pipe to join into your 100mm agy pipe. Or Blank any outlet of the Agy Tee to make it into a joiner or elbow.
The Bolted Trap Screw is designed for use in traffic areas, they also fit inside existing broken BTS for easy repairs.
Available in White, Grey or with Stainless Steel Top.
The 120mm X 200mm (large) Cupboard Plate may be used as a patch, or drilled to suit your needs, e.g., spa pumps, vanity basin services etc. You’ll never get caught on the job without the right size cupboard plate again. Cupboard plates can be knocked out over 50mm pipe & peeled out to accommodate the following sizes.
- 40mm DWV Pipe and 40mm Socket
- 50mm DWV Pipe and 50mm Socket
The 120mm Round (small) Cupboard Plate may be used as a patch, or drilled to suit your needs, e.g., spa pumps, vanity basin services, etc. You’ll never get caught on the job without the right size cupboard plate again. Cupboard plates can be knocked out over 50mm pipe & peeled out to accommodate the following sizes.
- 40mm DWV Pipe and 40mm Socket
- 50mm DWV Pipe and 50mm Socket
The Disposable Test Plug is used for water testing 100mm pipework. Place inside I.O.Pipe when you glue in the first upstream joint. Use screwdriver to puncture test plug and pry out to remove.
step 1. Insert test plug into I.O pipe socket before gluing your first pipe section.
Step 2. Release test water by cutting here.
Step 3. To remove plug - punch large screwdriver through plug and lever.
The 90mm Downpipe Expansion Joint Connects to 90 stormwater fittings, allows for over 100mm of expansion at the downpipe.
The Drainmaster was designed to overcome the difficulties Plumbers and Drainers experience with conventional stormwater pits. Not being able to achieve satisfactory surface finish height, Concreters and Landscapers often called upon the Plumber or Drainer to extend or lower the grate height. With the Drainmaster, it is a simple cut and glue procedure using PVC Weld cement, at the time when the Concreter and Landscaper is finishing off.
The Large inlet grate maximises water drain efficiency. It is designed for pedestrian traffic and has a strong grate and body with four internal pillar supports.
At 225mm X 225mm square, it sits about 85 mm deep when cut off for use with 100mm pipe, or about 115 mm deep when used with 90mm pipe. It can be used for shallow pipes simply by connecting a 90 degree X 90mm stormwater elbow to connect your pipe. It has been designed to fit into a few different pipe sizes and types which are:
